Painting Concrete Floors With Solvent Based Two Pack Epoxy

Painting Bare Concrete Floors with Solvent Based Two Pack Epoxy Floor Coating

 

(Suitable for all traffic)

 

 

Two coats of paint are always recommended 1st coat primes and seals the floor. 2nd coat provides good colour build, protection and longevity of the coating.

 

Be cautious of using solvent based two pack epoxy over existing floor coatings as solvents may attack the existing paint. If un-sure use solvent free or single pack floor paint.

 

 

Two Pack Epoxy Floor Paints

 

When painting any concrete floor it is important that the moisture content of the concrete is no greater than 5% and that there is an ambient temperature of 10˚C. Green concrete is best left for at least 2-3 months before coating. There are three main factors to ensure the epoxy coating will offer the protection & durability you require. They are floor preparation, method of mixing the two components and of course application. Any floor paint will require good floor preparation before coating. If time and effort is not but into preparing the floor before coating, then no matter how good a product is, or indeed how much it costs you to buy, the coatings potential will not be met.

 

PREPARATION

 

With any floor coating preparation is an essential key to extend the protection and lifespan of the coating. To prepare a bare (rough) concrete floor prior to painting we always recommend a light abrasion first; this can be done either by a scarifying machine or track blasting (most effective method). This allows the paint to create a good lock and key effect with the concrete which then leads to much better adhesion.

If the floor has been power floated or is generally very shiny, the floor paint will not adhere to this surface. It is recommended to trackblast the concrete to remove most of the top layer prior to painting. The structure of the top layer in a power floated concrete floor is generally unstable and easy to damage this is due to one small partial size been pushed to the top. If trackblasting in not an economical scenario, you can use a scarifying machine or a concentrated Acid Descaler to etch the floor.

After the floor has been abraded, we then recommend degreasing the area, removing dust and anyyd a the floor.ing ical hed to the top layer unstable and easily damaged.

the Christmas holidays they know the pa loose parts. If floors are heavily penetrated with any sort of contamination it is important to remove it all before coating, the most effective way is to have the floor steam cleaned. Remember this will add moisture into the floor, so time will have to be allowed for the moisture to escape. If the floor has light or no contamination just a quick mop around with our Degreasing Solvent or Acid Descaler will suffice. Again ‘preparation’ is key for a good floor coating, should any moisture or contamination be trapped in the substrate the paint will simply blister and blow off.

 

 

METHOD OF MIXING

 

Two Pack Epoxy as the name suggests has two component that must be mixed together thoroughly to ensure an even cure occurs. Two Pack Epoxy’s mixing ratio is 4 parts of paint to 1 part of Two Pack Epoxy Catalyst. Two Pack Epoxy as a Pack so there is no confusion to whether the customer needs to purchase the correct catalyst separately. It is important to thoroughly mix the paint 4:1 with the catalyst, we recommend mixing with a pneumatic drill and a mixing paddle, to ensure an even dispersion. If an epoxy is not mixed thoroughly the paint may not catalyse evenly leaving a patched of tacky paint which will never dry and will need cleaning up before trying to recoat – this is a very messy job! Once the paint has been mixed, let the paint stand for 10-15 minutes before starting to apply. Two Pack Epoxy has a pot life of around 8 hours.

 

APPLICATION

 

Two Pack Epoxy can be easily applied by brush, roller and suitable spray application. ENSURE THERE IS GOOD VENTILATION WHEN USING SOLVENT BASED PAINTS. Ensure the ambient temperature is 10˚C. Start to cut in the edges with a brush (use a good brush as this coating will start pulling bristles out of cheap brushes), then using our sheep simulated rollers or solvent resistant sleeves and tray, start to roll the first coat out; starting at the far end working back to the exiting door. Leave the first coat to dry for 12 hours or overnight before overcoating with the second coat. If the first coat has been left for 24 hours or more before overcoating then a light abrasion will be required for the second coat to adhere to the first. For the second coat simply follow the exact same instructions for the first coat.

 

Manufacturer’s guidelines are that any type of paint will need 7 days for the coating to reach its full properties. Obviously we know this is an unrealistic time scale for most companies or general public to not be able to use that area for such a long time, but if the coating is left for at least 24 hours this should be long enough for foot and heavier traffic. The longer the coating is left the longer it will last!